Wood professionals

Discover our entire catalogue.

Tools for circular cutting

Tools for circular cutting

Tools for circular cutting
(ZOBO1-01)


Tool for circular cutting with protective cover, TS-KK D13 circular cutting tool shaft, CB-KK HW 10x60 pilot drill and KF-KK pin wrench.
Maximum thickness of board to be cut: 43 mm.
Holder must be ordered separately.

Code
For type 1 holder D50-130mm and type 2 holder
With suction coupling D27 mm.
ZOBO762427
For type 1 holder D50-100 mm ZOBO762428
For type 1 holder D50-70 mm
Specially for switches/sockets made of wood.
ZOBO762429

Related products

Type 1 holder

Type 1 holder
(ZOBO1-02)

Type 1 holder with set of EK-KK type 1 cutters, set of 4 cutters, spacer washers 0.5 mm SR-KK 20x8x0.5, set of 20 cutters, tightening screw and Allen wrench of 5.
Maximum thickness of board to be cut: 43 mm.

Code
Adjustment range D50-55 mm ZOBO762466
Adjustment range D55-60 mm ZOBO762467
Adjustment range D60-65 mm ZOBO762468
Adjustment range D65-70 mm ZOBO762469
Adjustment range D70-80 mm ZOBO762470
Adjustment range D80-90 mm ZOBO762471
Adjustment range D90-100 mm ZOBO762472
Adjustment range D100-115 mm ZOBO762464
Adjustment range D115-130 mm ZOBO762465

Type 2 holder

Type 2 holder
(ZOBO1-03)

Type 2 holder with set of EEK-KK 50-130 carbide cutters, set of 4 cutters, spacer washers 0.5 mm SR-KK 20x8x0.5, set of 20 washers, spacers, adjustment tool, tightening screw and Allen wrench of 6.
Maximum thickness of board to be cut: 43 mm.

Code
Adjustment range D50-120 mm ZOBO762450

Set of tools for circular cutting

Set of tools for circular cutting
(ZOBO1-04)

In a SYSTAINER with wooden lining.
Adjustment range D50-120 mm.
Maximum thickness of board to be cut: 43 mm.

Complete set including references:
- ZOBO762427
- ZOBO762450

Code
Complete set of tools for circular cutting containing :
- Tool for circular cutting with suction coupling D27 mm - Type 2 holder
ZOBO762435

Related products

Tool shaft for circular cutting

Tool shaft for circular cutting
(ZOBO1-05)

Code
Tool shaft for circular cutting with hardened, ground shank
With drilled nut, depth adjusting ring, KF-KK pin wrench and pilot drill HW 10 mm CB-KK HW 10x60. For type 1 and 2 holders.
ZOBO762605
Tool shaft for short circular cutting
Without shank, M12 tap for connection to M12 thread shanks. Housing for pilot drill D10 mm. For type 1 and 2 holders.
ZOBO762606
Tool shaft for circular cutting with automatic ejector rod
Suitable for fixed station machines. Used without pilot drill With drilled nut, depth adjustment ring and KF-KK pin wrench. For type 1 holder of D60 mm and over.
ZOBO761967

Related products

Pilot drill and cutters

Pilot drill and cutters
(ZOBO1-06)

Code
Pilot drill HSS D10 mm
For use on tool shafts for circular carbide tools.
ZOBO762620
Set of cutters (4)
With carbide cutting edges for use in type 1 holders 2 cutters with tapered pre-cutters made of carbide 2 cutters with main cutting edges made of carbide
ZOBO623721
Set of cutters (4)
With carbide cutting edges for use in type 1 holders 2 cutters with tapered pre-cutters made of carbide 2 cutters with main cutting edges made of carbide
ZOBO762491

Related products

Spacer washers

Spacer washers
(ZOBO1-07)

Spacer washers for adjustment of the desired diameter on type 1 and 2 holders.

Code
Spacer washers 0.5 mm thick
To be placed on radius of holder. Changes the diameter by 0.2 mm. Pack of 4.
ZOBO762212
Spacer washer 0.1 mm thick
To be placed on the radius of the holder. Changes the diameter by 1 mm. Pack of 20.
ZOBO762210

Related products

Pin wrench

Pin wrench
(ZOBO1-08)

To tighten and release holders on tool shafts for circular cutting and the tools for circular cutting.